• Home
  • > Training & Events

Location

Category

Training & Events

We offer a wide breadth of training on our products and technologies. You'll find a full list of our training events below, or you can use the filters on the left to find specific events that interest you

AC/DC Motors and Drives Fundamentals

This course is a skill-building course that provides you with a basic understanding of AC and DC motor and drive concepts and terminology. At the completion of this course, you will have the necessary fundamental knowledge and skills required to attend other Rockwell

  • Course #: CCA101
    Duration: 2 Day(s)
    Cost: $1507.0

Application Code Manager and Library Objects Development

After completing this course, you should be able to:

  • Identify and register pre-configured Application Code Manager (ACM) library objects
  • Create and decorate Studio 5000® Library Objects
  • Create Application Code Manager (ACM) Library
  • Course #: CCP157
    Duration: 3 Day(s)
    Cost: $1808.0

Basic Electrical Concepts

This course provides information on the basic concepts of direct current (DC) electricity and magnetism, including electrostatics, basic circuit concepts, and measurement of electrical quantities and associated numerical concepts, Ohm’s Law, practical circuits,

  • Course #: EMS-100
    Duration: 5 Day(s)
    Cost: $2612.0

ControlLogix, FactoryTalk View ME, Kinetix 6000, And PowerFlex 40 Fundamentals And Troubleshooting

This course provides you with the skills necessary to maintain and troubleshoot:

  • Studio 5000 Logix Designer® applications that operate on a ControlLogix® platform
  • FactoryTalk® View Machine Edition (ME) applications that run on
  • Duration: 5 Day(s)
    Cost: $2612.0

Essentials of Industrial Ethernet Networks for an OT Professional

After completing this course, you should be able to:

  • Demonstrate understanding of basic Ethernet networking skills, terminology, and concepts
  • Apply these skills when performing advanced network specification, configuration, and troubleshooting
  • Course #: CCP182
    Duration: 2 Day(s)
    Cost: $1507.0

Ethernet/IP Configuration and Troubleshooting

This course should prepare you to effectively:

  • Configure a Stratix® switch (5700, 8000, and/or 8300) to meet a variety of network requirements
  • Assign IP addresses to devices on an EtherNet/IP network using rotary switches and a variety of
  • Course #: CCP183
    Duration: 3 Day(s)
    Cost: $1808.0

FactoryTalk View SE Programming

Upon completion of this course, you should be able to organize and develop FactoryTalk View Site Edition (SE) applications. This course provides opportunities for you to work with local FactoryTalk View SE applications. During class, you will have the opportunity to practice

  • Course #: CCV207
    Duration: 5 Day(s)
    Cost: $2612.0

FactoryTalk® AssetCentre System Design & Implementation

This course provides you with the skills required to use FactoryTalk® AssetCentre software to maximize your control system investment and manage assets effectively. Throughout the course, you will learn how to design a FactoryTalk AssetCentre system, install and configure

  • Course #: FTAC
    Duration: 3 Day(s)
    Cost: $1808.0

FactoryTalk® View ME & PanelView™ Plus Programming

This course is a skill-building course that provides you with the skills necessary to develop FactoryTalk View Machine Edition (ME) applications that run on the next-generation PanelView™ Plus terminals.

This course provides opportunities to work with both the

  • Course #: CCV204
    Duration: 2 Day(s)
    Cost: $2221.0

Functional Safety for Machinery Introduction

The standards regarding functional safety and relevant laws and directives demand that people and organizations performing responsible (accountable) tasks during all relevant life cycle phases of a machine must achieve and prove the required competencies.

This is an

  • Course #: SAF-TUV1
    Duration: 3 Day(s)
    Cost: $1808.0

Functional Safety for Machinery Technician Certification

The standards regarding functional safety and relevant laws and directives demand that people and organizations performing responsible (accountable) tasks during relevant life cycle phases of a machine must achieve and prove required competencies.

In this training,

  • Course #: SAF-TUV0T
    Duration: 2 Day(s)
    Cost: $2009.0

Fundamentals of VFD Wiring and Commissioning

Overview: At the completion of this class, students will be able to install, wire, and commission a VFD for various applications.

This three day class will cover VFD theory, motor theory, input protection, output protection, dynamic braking, encoder feedback, safety

  • Course #: VFD1
    Duration: 3 Day(s)
    Cost: $1695.0

GuardLogix® Application Development

Upon completion of this course, you will be able to create a Logix Designer project for a GuardLogix system. You will have the opportunity to develop and practice these skills by:

  • Creating and configuring a GuardLogix project:
    • Configuring controller
  • Course #: SAF-LOG101
    Duration: 3 Day(s)
    Cost: $1507.0

GuardLogix® Development, Maintenance & Troubleshooting

Upon completion of this course, you will be able to create a Logix Designer project for a GuardLogix system. You will have the opportunity to develop and practice these skills by:

  • Creating and configuring a GuardLogix project:
    • Configuring controller
  • Course #: SAF-LOG101 & 103
    Duration: 3 Day(s)
    Cost: $2412.0

GuardLogix® Fundamentals and Troubleshooting

This course will assist you in developing and building a solid foundation with a fundamental knowledge of a GuardLogix® system. Upon completion of this course, you should be able to efficiently troubleshoot a previously operational GuardLogix system.

You will have

  • Course #: SAF-LOG103
    Duration: 1 Day(s)
    Cost: $905.0

Industrial Electrical Controls Fundamentals

This course is designed to provide knowledge and skills required to install, maintain and troubleshoot machine controls. At the completion of this course, you will be able to:

  • Define the safety considerations that must be observed when installing, checking or
  • Course #: MFG213
    Duration: 4 Day(s)
    Cost: $2221.0

Industrial Electronics

This course provides information on the function and circuit analysis of power supplies, amplifiers, integrators, comparators, and oscillators.

Upon completion of this course, you should be able to:

• Discuss the characteristics and uses of semiconductor

  • Duration: 3 Day(s)
    Cost: $1808.0

Introduction to the Integrated Architecture System

After completing this course, you should be able to work with the Integrated Architecture® system and automation system technology, such as DeviceNet, ControlNet, EtherNet/IP, and the Studio 5000® engineering environment.

This course will assist you in

  • Course #: CIA101
    Duration: 2 Day(s)
    Cost: $1507.0

Kinetix® 6000 Troubleshooting and Project Interpretation

This course is intended to provide you with the skills required to diagnose common problems on a Kinetix 6000 system. During class, you will practice operating and troubleshooting the system through hands-on exercises using the Studio 5000™ Logix Designer

  • Course #: CCN200
    Duration: 3 Day(s)
    Cost: $1507.0

Logix5000™ Maintainer Certificate

This accelerated course is for individuals who can quickly learn and apply Logix5000™ concepts, terminology, hardware troubleshooting skills, and interpretation of ladder logic in a Studio 5000 Logix Designer® project.

This course prepares you for the

  • Course #: CCP300
    Duration: 5 Day(s)
    Cost: $2612.0

Logix5000™ Programmer Certificate

This accelerated course is for individuals who can quickly learn and apply Logix5000™ concepts, terminology, hardware, and the Studio 5000 Logix Designer® programming environment.

You will quickly move from these early concepts to using producer/ consumer

  • Course #: CCP250
    Duration: 5 Day(s)
    Cost: $2612.0

Managing Industrial Networks with Cisco® Networking Technologies

Managing Industrial Networks with Cisco® Networking Technologies(IMINS) Version1.1 is a lab-based course which helps students with the foundational skills needed for the management and administration of networked industrial control systems. The IMINS course, developed in

  • Course #: IMINS
    Duration: 5 Day(s)
    Cost: $5821.0

Motion Control Fundamentals

Upon completion of this course, you should be able to demonstrate fundamental motion control concepts common to all Rockwell Automation motion control systems. This course is designed to provide you with an understanding of the concepts, terminology, functionality and

  • Course #: CCN130
    Duration: 2 Day(s)
    Cost: $1507.0

Motion Control Fundamentals Using Kinetix 5700 (CIP) Servo Drives

This is a two-day event. 

  • Duration: 3 Day(s)
    Cost: $1808.0

Motor Control and Troubleshooting

This course provides information on the concepts associated with systematic troubleshooting of instrumentation systems. Participants use practical application of troubleshooting techniques in exercise scenarios.

Upon completion of this course, you should be able

  • Duration: 5 Day(s)
    Cost: $2612.0

NFPA 70E 2015 - Electrical Safety and Arc Flash Compliance

The purpose of this course is to provide the student with an in-depth understanding of the current requirements of NFPA 70E® 2018. A complete presentation of the standard will be provided, along with the examples and exercises covering the tables and calculation methods

  • Course #: SAF-SFT11218
    Duration: 2 Day(s)
    Cost: $905.0

PLC Wiring & Troubleshooting

At the completion of this training, the participant will be able to “talk through” and troubleshoot the PLC’s ladder logic using the Logix5000 software in order to locate a “real” faulty input or output device, replace it, and get the process

  • Duration: 4 Day(s)
    Cost: $1895.0

PowerFlex® 750-Series Configuration & Startup

Upon completion of this course, given a wired PowerFlex 750-Series drive (PowerFlex 753 or PowerFlex 755) and AC motor, you will be able to start up the drive and configure drive parameters to meet application needs.

Throughout the course, you will have the chance to

  • Course #: CCA182
    Duration: 1 Day(s)
    Cost: $1507.0

PowerFlex® 750-Series Maintenance and Troubleshooting

This skill-building course introduces concepts and techniques that will assist you in successfully maintaining and troubleshooting a PowerFlex 750-Series (PowerFlex 753 or PowerFlex 755) drive. You will learn how to recognize PowerFlex 750-Series drive hardware and properly

  • Course #: CCA183
    Duration: 2 Day(s)
    Cost: $1507.0

Safety Enterprise Strategy Series Part 2: A Closer Look at Lockout/Tagout Program Management

The Safety Enterprise Strategy webinar series is designed to equip safety managers and safety champions with the knowledge to develop and maintain sustainable safety programs that can be implemented at a site-wide or multi-site scale.  The series will identify how the

  • Duration: 1 Day(s)
    Cost: $0.0

Safety Enterprise Strategy Series Part 3: Incorporating Machine Safety at an Enterprise Scale

The Safety Enterprise Strategy webinar series is designed to equip safety managers and safety champions with the knowledge to develop and maintain sustainable safety programs that can be implemented at a site-wide or multi-site scale.  The series will identify how the

  • Duration: 1 Day(s)
    Cost: $0.0

Safety Enterprise Strategy Series Part 4: Effective Strategies for Developing and Maintaining your Arc Flash Program

The Safety Enterprise Strategy webinar series is designed to equip safety managers and safety champions with the knowledge to develop and maintain sustainable safety programs that can be implemented at a site-wide or multi-site scale.  The series will identify how the

  • Duration: 1 Day(s)
    Cost: $0.0

Safety Relays and Devices Maintenance and Troubleshooting

This course will introduce you to monitoring safety relays and input and output devices used to configure safety systems according to industry standards for functional safety of machinery.

You will have the opportunity for hands-on experience with several of these

  • Course #: SAF-COM101
    Duration: 2 Day(s)
    Cost: $1507.0

Studio 5000™ Logix Designer Level 1: CompactLogix Fundamentals and Troubleshooting

 

Upon completion of this course, you should be able to troubleshoot a previously operational ControlLogix system and restore normal operation. In this course you will develop and practice these skills by:

 

  • Learning basic concepts and
  • Course #: CCP298
    Duration: 5 Day(s)
    Cost: $2612.0

Studio 5000™ Logix Designer Level 1: ControlLogix Fundamentals And Troubleshooting

Upon completion of this course, you should be able to troubleshoot a previously operational ControlLogix system and restore normal operation. You will have the opportunity to develop and practice these skills by:

  • Learning basic concepts and terminology used
  • Course #: CCP299
    Duration: 5 Day(s)
    Cost: $2612.0

Studio 5000™ Logix Designer Level 1: ControlLogix System Fundamentals

You will be introduced to basic Logix5000 concepts and terminology, and you will be exposed to Logix5000 system hardware, including hands-on experience with the ControlLogix platform.After completing this course, you should be able to perform basic ControlLogixand Studio 5000

  • Course #: CCP146
    Duration: 2 Day(s)
    Cost: $1507.0

Studio 5000™ Logix Designer Level 2: Basic Ladder Logic Programming

This course is a skill-building course that provides you with the resources and hands-on practice required to program basic ladder logic instructions for any Logix5000™ controller.

You will have an opportunity to use the Studio 5000 Logix Designer™

  • Course #: CCP151
    Duration: 2 Day(s)
    Cost: $1507.0

Studio 5000™ Logix Designer Level 2: ControlLogix Maintenance and Troubleshooting

Upon completion of this course, you will be able to troubleshoot a previously operational ControlLogix system and restore normal operation. This course adds to your skill set by introducing new tasks such as connecting to a network, interpreting project execution, editing

  • Course #: CCP153
    Duration: 4 Day(s)
    Cost: $2221.0

Studio 5000™ Logix Designer Level 3: Project Development

Upon completion of this course, given a functional specification for a Logix5000 application, you should be able to develop a project to meet the requirements of the specification. This course covers tasks common to the following controllers, which all use the Logix5000

  • Course #: CCP143
    Duration: 4 Day(s)
    Cost: $2221.0

ThinManager Configuration

ThinManager® is a thin client platform with an architecture that allows for deployment of less-expensive hardware. This gives users familiar applications and tools in a format that reduces management and maintenance costs while increasing security.

This course is

  • Course #: SPE201-LD
    Duration: 2 Day(s)
    Cost: $1507.0

Copyright © 2018  McNaughton-McKay  All Rights Reserved.