• Home
  • > Training & Events

Location

Category

Training & Events

We offer a wide breadth of training on our products and technologies. You'll find a full list of our training events below, or you can use the filters on the left to find specific events that interest you

AC/DC Motors & Drives Fundamentals

This course is a skill-building course that provides you with a basic understanding of AC and DC motor and drive concepts and terminology. At the completion of this course, you will have the necessary fundamental knowledge and skills required to attend other Rockwell

  • Course #: CCA101
    Duration: 2 Day(s)
    Cost: $1600.0

Accelerated Logix5000™ Maintainer Certificate

This accelerated course is for individuals who can quickly learn and apply Logix5000™ concepts, terminology, hardware troubleshooting skills, and interpretation of ladder logic in a Studio 5000 Logix Designer® project.

This course prepares you for the

  • Course #: CCP300
    Duration: 5 Day(s)
    Cost: $2780.0

Accelerated Logix5000™ Programmer Certificate

This accelerated course is for individuals who can quickly learn and apply Logix5000™ concepts, terminology, hardware, and the Studio 5000 Logix Designer® programming environment.

You will quickly move from these early concepts to using producer/ consumer

  • Course #: CCP250
    Duration: 5 Day(s)
    Cost: $2780.0

Advanced Logix5000™ Programmer Certificate

This course is for individuals who can quickly learn and apply Logix 5000™ concepts, terminology, hardware, and the Studio 5000 Logix Designer® programming environment.

You will learn about more advanced programming methods and instructions, project

  • Course #: CCP251
    Duration: 4 Day(s)
    Cost: $2360.0

Centrifugal Pumps

This course provides information on the concepts associated with centrifugal pump application, operation, hazards, troubleshooting and repair common problems.  It also explains how to draw and label simple pump curves.  There are hands-on exercises for inspection and repair of pumps and its associated equipment.

  • Course #: MMS-200
    Duration: 3 Day(s)
    Cost: $1920.0

Essentials of Industrial Ethernet Networks for an OT Professional

In this course, you will learn how to verify communications between devices, recognize data transmission types, and differentiate between OSI Model Layer 2 and Layer 3 switching functions.

You will also identify the routing process, monitor a switch using Device

  • Course #: CCP182
    Duration: 2 Day(s)
    Cost: $1600.0

Ethernet 101: What Every Controls Person Should Know About IT

Ethernet is now the backbone of industrial automation networking. It is the protocol that every manufacturer uses and has wound its way into every aspect of automation and controls systems.

Join McNaughton-McKay Electric Company for this seminar tailored to the needs

  • Duration: 1 Day(s)
    Cost: $0.0

Ethernet/IP Configuration and Troubleshooting

This course should prepare you to effectively:

  • Configure a Stratix® switch (5700, 8000, and/or 8300) to meet a variety of network requirements
  • Assign IP addresses to devices on an EtherNet/IP network using rotary switches and a variety of
  • Course #: CCP183
    Duration: 3 Day(s)
    Cost: $1920.0

FactoryTalk EnergyMetrix® Software Configuration in an Energy Monitoring System

With FactoryTalk EnergyMetrix, you can capture, analyze, store, and share energy data across your entire enterprise using a simple Web browser. This makes it easy to distribute the knowledge you need to optimize energy consumption, which can help improve productivity while

  • Course #: FTEM
    Duration: 2 Day(s)
    Cost: $1600.0

FactoryTalk Historian Site Edition Configuration and Data Collection

This course will provide you with an overview of the various FactoryTalk® Historian tools for collecting data. You will learn how to configure a FactoryTalk Historian Site Edition system.

The course also covers how to use Microsoft Excel to create and modify

  • Course #: RS-FTHSEC
    Duration: 4 Day(s)
    Cost: $2360.0

FactoryTalk Metrics Configuration

FactoryTalk® Metrics is a complete, windows-based solution for the analysis of time-series process and production data. FactoryTalk Metrics provides a set of tools to analyze the performance of production assets. FactoryTalk Metrics provides a performance rating, based on

  • Course #: FTM
    Duration: 3 Day(s)
    Cost: $1920.0

FactoryTalk View ME and PanelView Plus Maintenance and Troubleshooting

This course provides you with the skills necessary to maintain and troubleshoot FactoryTalk® View Machine Edition (ME) applications that run on PanelView™ Plus 7 terminals. This course provides opportunities to work with both the hardware and

  • Course #: CCV209-A
    Duration: 2 Day(s)
    Cost: $1600.0

FactoryTalk View SE Programming

Upon completion of this course, you should be able to organize and develop FactoryTalk View Site Edition (SE) applications. This course provides opportunities for you to work with local FactoryTalk View SE applications. During class, you will have the opportunity to practice

  • Course #: CCV207
    Duration: 5 Day(s)
    Cost: $2780.0

FactoryTalk® VantagePoint Configuration and Reporting

In this course, you will learn various tools to analyze and display data using FactoryTalk VantagePoint EMI. The course covers how to use the analysis and reporting tools to create Trends, Excel Reports, and Dashboards. You will have an opportunity to use the Portal and

  • Course #: FTVP
    Duration: 3 Day(s)
    Cost: $1920.0

FactoryTalk® View ME & PanelView™ Plus Programming

After completing this course, given a computer with FactoryTalk® View Machine Edition (ME) software and a PanelView™ Plus 7 terminal, you should be able to produce an operational application running on the terminal.

During class, you will practice the

  • Course #: CCV204-A
    Duration: 4 Day(s)
    Cost: $2360.0

GuardLogix® Application Development and Troubleshooting

Upon completion of this course, you will be able to create a Studio 5000 Logix Designer® project for a GuardLogix® system and troubleshoot a previously operational GuardLogix system.

You will have the opportunity to develop and practice these skills

  • Course #: SAF-LOG104
    Duration: 3 Day(s)
    Cost: $1920.0

Hydraulics and Pneumatics Fundamentals

This course provides information on the concepts associated with hydraulics, hydraulic systems and components, fluid principles, hydraulic system design, and hydraulic schematic symbology.

Upon completion of this course, you should be able to:
• Describe the

  • Course #: MMS-125
    Duration: 3 Day(s)
    Cost: $1920.0

Improving Electrical Safety with Short Circuit Protection

This is a complimentary seminar, no charge.

ABOUT THIS SEMINAR

  • New incident energy equations in the 2018 edition of IEEE 1584 may provide different results than existing
  • Duration: 1 Day(s)
    Cost: $0.0

Industrial Electrical Controls Fundamentals

This course is designed to provide knowledge and skills required to install, maintain and troubleshoot machine controls. At the completion of this course, you will be able to:

  • Define the safety considerations that must be observed when installing, checking or
  • Course #: MFG213
    Duration: 4 Day(s)
    Cost: $2360.0

Kinetix 5700 Troubleshooting and Project Interpretation

Upon completion of this course, you will be able to apply maintenance and troubleshooting techniques to diagnose and correct common problems which may occur with a Kinetix® 5700 servo drive system.

You will practice operating and troubleshooting the system through

  • Course #: CCN202
    Duration: 3 Day(s)
    Cost: $1920.0

Managing Industrial Networks with Cisco® Networking Technologies

Managing Industrial Networks with Cisco® Networking Technologies(IMINS) Version1.1 is a lab-based course which helps students with the foundational skills needed for the management and administration of networked industrial control systems. The IMINS course, developed in

  • Course #: IMINS
    Duration: 5 Day(s)
    Cost: $3960.0

Motion Control Fundamentals using Kinetix 5700 (CIP) Servo Drives

Upon completion of this course, you should be able to demonstrate fundamental motion control concepts common to all Rockwell Automation motion control systems.

This course is designed to provide you with an understanding of the concepts, terminology, functionality and

  • Course #: CCN132
    Duration: 3 Day(s)
    Cost: $1920.0

Motor Control and Troubleshooting

This course provides information on the concepts associated with systematic troubleshooting of instrumentation systems. Participants use practical application of troubleshooting techniques in exercise scenarios.

Upon completion of this course, you should be able

  • Course #: EMS-230
    Duration: 5 Day(s)
    Cost: $2780.0

OSHA 1910.147 - Control of Hazardous Energy (Lockout/Tagout)

CFR 1910.147, Control of Hazardous Energy (Lockout/Tagout) continues to be one of the top 10 most cited violations by OSHA in the industry. Bureau of Labor Statistics data reports a total of 57,250 injuries in five year period from 2011 to 2017 in maintenance,

  • Duration: 1 Day(s)
    Cost: $0.0

PLC Wiring & Troubleshooting

At the completion of this training, the participant will be able to “talk through” and troubleshoot the PLC’s ladder logic using the Logix5000 software in order to locate a “real” faulty input or output device, replace it, and get the process

  • Duration: 4 Day(s)
    Cost: $1895.0

PLC-5®/SLC™ 500 and RSLogix™ Fundamentals

Upon completion of this course, you will be able to perform the following tasks:

• Identify the main components of programmable controller systems and describe their functions
• Describe the flow of information through a programmable controller system

  • Course #: CCP122
    Duration: 2 Day(s)
    Cost: $1600.0

Pipefitting

This course provides information on the codes and standards, types of piping and associated components, specifications, and fitting and supporting techniques.

  • Course #: MMS-250
    Duration: 5 Day(s)
    Cost: $2780.0

Positive Displacement Pumps

This course provides information on the concepts associated with positive displacement pump application, operation, hazards, troubleshooting and repair common problems.

  • Course #: MMS-205
    Duration: 2 Day(s)
    Cost: $1600.0

PowerFlex® 525 Drive Startup & Configuration

Upon completion of this course, given a wired PowerFlex® 525 drive and AC motor, you will be able to properly start up the drive and configure drive parameters to meet application-specific needs.

Throughout the course, you will have the chance to use a variety of

  • Course #: CCA185
    Duration: 1 Day(s)
    Cost: $963.0

PowerFlex® 750-Series Configuration & Startup

Upon completion of this course, given a wired PowerFlex 750-Series drive (PowerFlex 753 or PowerFlex 755) and AC motor, you will be able to start up the drive and configure drive parameters to meet application needs.

Throughout the course, you will have the chance to

  • Course #: CCA182
    Duration: 2 Day(s)
    Cost: $1600.0

PowerFlex® 750-Series Maintenance & Troubleshooting

This skill-building course introduces concepts and techniques that will assist you in successfully maintaining and troubleshooting a PowerFlex 750-Series (PowerFlex 753 or PowerFlex 755) drive. You will learn how to recognize PowerFlex 750-Series drive hardware and properly

  • Course #: CCA183
    Duration: 2 Day(s)
    Cost: $1600.0

SLC™ 500 & RSLogix™ 500 Maintenance & Troubleshooting

This skill-building course provides you with the necessary practice needed to interpret, isolate, and diagnose common hardware problems related to noise, power, and discrete and analog I/O. In troubleshooting scenarios, you will be introduced to basic ladder logic

  • Course #: CCPS43
    Duration: 4 Day(s)
    Cost: $2360.0

Safety Relays and Devices Maintenance and Troubleshooting

This course will introduce you to monitoring safety relays and input and output devices used to configure safety systems according to industry standards for functional safety of machinery.

You will have the opportunity for hands-on experience with several of these

  • Course #: SAF-COM101
    Duration: 2 Day(s)
    Cost: $1600.0

Shaft and Coupling Alignment

This course provides information on the importance of proper alignment and alignment methods, cause of misalignment and how to correct for error such as soft foot and thermal growth using dial indicators, and coupling alignment using dial indicators and lasers where applicable.  There are hands-on exercises for shaft and equipment alignments.

  • Course #: MMS-245
    Duration: 5 Day(s)
    Cost: $2780.0

Studio 5000™ Logix Designer Level 1: CompactLogix Fundamentals and Troubleshooting

Upon completion of this course, you should be able to troubleshoot a previously operational ControlLogix system and restore normal operation. In this course you will develop and practice these skills by:

  • Learning basic concepts and terminology used
  • Course #: CCP298
    Duration: 5 Day(s)
    Cost: $2612.0

Studio 5000™ Logix Designer Level 1: ControlLogix Fundamentals and Troubleshooting

Upon completion of this course, you should be able to troubleshoot a previously operational ControlLogix system and restore normal operation. You will have the opportunity to develop and practice these skills by:

  • Learning basic concepts and terminology used
  • Course #: CCP299
    Duration: 5 Day(s)
    Cost: $2780.0

Studio 5000™ Logix Designer Level 1: ControlLogix System Fundamentals

You will be introduced to basic Logix5000 concepts and terminology, and you will be exposed to Logix5000 system hardware, including hands-on experience with the ControlLogix platform.After completing this course, you should be able to perform basic ControlLogixand Studio 5000

  • Course #: CCP146
    Duration: 2 Day(s)
    Cost: $1600.0

Studio 5000™ Logix Designer Level 2: Basic Ladder Logic Programming

This course is a skill-building course that provides you with the resources and hands-on practice required to program basic ladder logic instructions for any Logix5000™ controller.

You will have an opportunity to use the Studio 5000 Logix Designer™

  • Course #: CCP151
    Duration: 2 Day(s)
    Cost: $1600.0

Studio 5000™ Logix Designer Level 2: ControlLogix Maintenance & Troubleshooting

Upon completion of this course, you will be able to troubleshoot a previously operational ControlLogix system and restore normal operation. This course adds to your skill set by introducing new tasks such as connecting to a network, interpreting project execution, editing

  • Course #: CCP153
    Duration: 4 Day(s)
    Cost: $2360.0

Studio 5000™ Logix Designer Level 3: Basic Ladder Logic Interpretation

This course is a skill-building course that provides you with a more detailed understanding of Studio 5000 Logix Designer™ ladder logic instructions and terminology. This course also provides you with the resources and hands-on practice required to interpret ladder

  • Course #: CCCL21
    Duration: 2 Day(s)
    Cost: $1600.0

Studio 5000™ Logix Designer Level 3: Project Development

Upon completion of this course, given a functional specification for a Logix5000 application, you should be able to develop a project to meet the requirements of the specification. This course covers tasks common to the following controllers, which all use the Logix5000

  • Course #: CCP143
    Duration: 4 Day(s)
    Cost: $2360.0

Studio 5000™ Logix Designer Level 4: Kinetix 5700 (CIP) Programming

After completing this course, you should be able to configure, test, tune, and program CIP Motion™ axes using the Studio 5000 Logix Designer® application.

Building upon the skills gained in the Studio 5000 Logix Designer Level 3: Project Development (CCP143)

  • Course #: CCN144-A
    Duration: 4 Day(s)
    Cost: $2360.0

ThinManager® Configuration

ThinManager® is a thin client platform with an architecture that allows for deployment of less-expensive hardware. This gives users familiar applications and tools in a format that reduces management and maintenance costs while increasing security.

This course is

  • Course #: SPE201-LD
    Duration: 2 Day(s)
    Cost: $1600.0

Valve Repair

This course provides information on valve maintenance and repair activities associated with common valves used in industrial applications. This course assumes that the student is familiar with valve fundaments.

  • Course #: MMS-210
    Duration: 5 Day(s)
    Cost: $2780.0

Vibration Analysis Fundamentals

This course is designed for the new user of vibration analysis or predictive maintenance instrumentation or for the individual that desires to become more familiar with the basics of vibration.  The relationship between the mechanical condition of machinery and vibration

  • Course #: EK-ICM101
    Duration: 3 Day(s)
    Cost: $1920.0

Vibration Analysis: Level 1

This course presents the fundamental information necessary to implement and operate a successful predictive maintenance program. Vibration basics and the relationship between vibration and machinery condition are reviewed.  Proven techniques for specifying meaningful

  • Course #: EK-ICM201
    Duration: 4 Day(s)
    Cost: $2360.0

Copyright © 2019  McNaughton-McKay  All Rights Reserved.